Next: SXML, Previous: Curried Definitions, Up: Guile Modules [Contents][Index]
Statprof is a statistical profiler for Guile.
A simple use of statprof would look like this:
(use-modules (statprof))
(statprof (lambda ()
(map 1+ (iota 1000000))
#f))
This would run the thunk with statistical profiling, finally displaying a flat table of statistics which could look something like this:
% cumulative self time seconds seconds procedure 57.14 39769.73 0.07 ice-9/boot-9.scm:249:5:map1 28.57 0.04 0.04 ice-9/boot-9.scm:1165:0:iota 14.29 0.02 0.02 1+ 0.00 0.12 0.00 <current input>:2:10 --- Sample count: 7 Total time: 0.123490713 seconds (0.201983993 seconds in GC)
All of the numerical data with the exception of the calls column is statistically approximate. In the following column descriptions, and in all of statprof, “time” refers to execution time (both user and system), not wall clock time.
The % time column indicates the percentage of the run-time time
spent inside the procedure itself (not counting children). It is
calculated as self seconds, measuring the amount of time spent in
the procedure, divided by the total run-time.
cumulative seconds also counts time spent in children of a
function. For recursive functions, this can exceed the total time, as
in our example above, because each activation on the stack adds to the
cumulative time.
Finally, the GC time measures the time spent in the garbage collector. On systems with multiple cores, this time can be larger than the run time, because it counts time spent in all threads, and will run the “marking” phase of GC in parallel. If GC time is a significant fraction of the run time, that means that most time in your program is spent allocating objects and cleaning up after those allocations. To speed up your program, one good place to start would be to look at how to reduce the allocation rate.
Statprof’s main mode of operation is as a statistical profiler. However
statprof can also run in a “precise” mode as well. Pass the
#:count-calls? #t keyword argument to statprof to record
all calls:
(use-modules (statprof))
(statprof (lambda ()
(map 1+ (iota 1000000))
#f)
#:count-calls? #t)
The result has an additional calls column:
% cumulative self time seconds seconds calls procedure 82.26 0.73 0.73 1000000 1+ 11.29 420925.80 0.10 1000001 ice-9/boot-9.scm:249:5:map1 4.84 0.06 0.04 1 ice-9/boot-9.scm:1165:0:iota [...] --- Sample count: 62 Total time: 0.893098065 seconds (1.222796536 seconds in GC)
As you can see, the profile is perturbed: 1+ ends up on top,
whereas it was not marked as hot in the earlier profile. This is
because the overhead of call-counting unfairly penalizes calls. Still,
this precise mode can be useful at times to do algorithmic optimizations
based on the precise call counts.
The profiler works by setting the unix profiling signal
ITIMER_PROF to go off after the interval you define in the call
to statprof-reset. When the signal fires, a sampling routine
runs which crawls up the stack, recording all instruction pointers into
a buffer. After the sample is complete, the profiler resets profiling
timer to fire again after the appropriate interval.
Later, when profiling stops, that log buffer is analyzed to produce the “self seconds” and “cumulative seconds” statistics. A procedure at the top of the stack counts toward “self” samples, and everything on the stack counts towards “cumulative” samples.
While the profiler is running it measures how much CPU time (system and
user – which is also what ITIMER_PROF tracks) has elapsed while
code has been executing within the profiler. Only run time counts
towards the profile, not wall-clock time. For example, sleeping and
waiting for input or output do not cause the timer clock to advance.
Profile the execution of thunk, and return its return values.
The stack will be sampled hz times per second, and the thunk itself will be called loop times.
If count-calls? is true, all procedure calls will be recorded. This operation is somewhat expensive.
After the thunk has been profiled, print out a profile to
port. If display-style is flat, the results will be
printed as a flat profile. Otherwise if display-style is
tree, print the results as a tree profile.
Note that statprof requires a working profiling timer. Some
platforms do not support profiling timers. (provided?
'ITIMER_PROF) can be used to check for support of profiling timers.
Profiling can also be enabled and disabled manually.
Returns #t if statprof-start has been called more times
than statprof-stop, #f otherwise.
Start or stop the profiler.
Reset the profiling sample interval to sample-seconds and sample-microseconds. If count-calls? is true, arrange to instrument procedure calls as well as collecting statistical profiling data.
If you use the manual statprof-start/statprof-stop
interface, an implicit statprof state will persist starting from the
last call to statprof-reset, or the first call to
statprof-start. There are a number of accessors to fetch
statistics from this implicit state.
Returns the time accumulated during the last statprof run.
Returns the number of samples taken during the last statprof run.
Fold proc over the call-data accumulated by statprof. This procedure cannot be called while statprof is active.
proc will be called with arguments, call-data and prior-result.
Returns the call-data associated with proc, or #f if none
is available.
Accessors for the fields in a statprof call-data object.
Returns an object of type statprof-stats.
Accessors for the fields in a statprof-stats object.
Displays a summary of the statistics collected. Possible values for style include:
flatDisplay a traditional gprof-style flat profile.
anomaliesFind statistical anomalies in the data.
treeDisplay a tree profile.
Returns a list of stacks, as they were captured since the last call to
statprof-reset.
Return a call tree for the previous statprof run.
The return value is a list of nodes. A node is a list of the form:
@code
node ::= (@var{proc} @var{count} . @var{nodes})
@end code
The @var{proc} is a printable representation of a procedure, as a
string. If @var{precise?} is false, which is the default, then a node
corresponds to a procedure invocation. If it is true, then a node
corresponds to a return point in a procedure. Passing @code{#:precise?
#t} allows a user to distinguish different source lines in a procedure,
but usually it is too much detail, so it is off by default.
Like the statprof procedure, but instead of profiling CPU time,
we profile garbage collection.
The stack will be sampled soon after every garbage collection during the evaluation of thunk, yielding an approximate idea of what is causing allocation in your program.
Since GC does not occur very frequently, you may need to use the loop parameter, to cause thunk to be called loop times.
Next: SXML, Previous: Curried Definitions, Up: Guile Modules [Contents][Index]